We also stock Dowel Pin, Expansion, Taper Shank, Taper Pipe, Taper Pin, Construction, Capscrew, Safety, Bridge and Hand Reamers – all of which are available at affordable prices and with same day shipping. Reamers are primarily used to remove material from, deburr, or enlarge the inside of previously formed holes such as I-Beams, Angles, Channels and Plates. They have cutting flutes on one end and a straight shank on the other. Reamers can either be used with hand or machine tools, such as turret lathes and drill presses used in metalworking. Reamers used with machines are called chucking reamers. They cut on the 45-degree bevel lead; the bevel lead is the angle at the top of the flute. Hand reamers cut both on the bevel lead and the taper lead, which is the full length of the flute. There are also taper pin reamers, which are designed to ream holes for standard taper pins. Taper pin reamers are used with both hand and machine tools. The number of flutes on the reamer determines how fast it can be fed into the hole, how rigid it is, and the space for chips. The more flutes, the more space, feed speed, and rigidity. The type of flute also comes into play. Straight flutes are commonly used, but spiral and helical flutes prevent chip buildup and can be used at higher speeds.
Chucking reamers are most often used in machine shops for close tolerance work. They are designed to remove a minimal amount of stock, usually between 1/64" to 1/32", for a close tolerance hole. Chucking Reamers are available in a variety of different styles such as Straight Flute, Right Hand Spiral, Left Hand Spiral and Intermediate Sizes.
The left hand spiral flute design pushes chips forward out of the hole and allows the reamer to be used in holes that have an interruption. Ground with a starting chamfer to provide easy entry of the reamer in to the hole.
Left Hand Spiral Hand Reamers are designed to enlarge reamed holes by a few thousandths. Left hand spiral is for reaming keyways and interrupted cut holes. The pilot and guide on these reamers are ground slightly undersize for clearance and to guide reamer. The flutes also have a ground starting taper to help guide reamer into hole.
All of our HSS (High Speed Steel) Taper Reamers are designed for reaming holes so that standard taper pins can fit properly. The results will be attained if the hole is drilled a few thousandths smaller than the small diameter of the finished reamed hole.
All of our HSS (High Speed Steel) Dowel Pin Reamers are manufactured with a minus tolerance, used for reaming holes for dowel pins in the automotive industry and mold shops.
Expansion reamers are precision tools that can be reused multiple times and are generally used for reaming abrasive material. They are built with slots cut between the flutes and a tapered screw in the head. As the reamer is used and the cutting edges are worn down, the user simply turns the screw to expand the reamer, re-clears it, sharpens it back to its original size and goes right back to work. Expansion reamers are handy tools that allow the user to keep working with the same reamer multiple times, without having to buy a new reamer.
Our HSS (High Speed Steel) Cap Screw Counterbores are designed to create a recess for socket head cap screws and shoulder screws.
Our HSS (High Speed Steel) Safety Reamers are especially adapted for heavy duty reaming as encountered in structural steel assembly fabrication. They are tapered at the point which allows you to enter holes that are out of alignment.
Our HSS (High Speed Steel) Bridge Reamers are commonly used for bridgework, ship construction and structural steel fabrication where diameter accuracy is important. Bridge Reamers have pilot type points for the best alignment possible and allows easy entry into small, off-center holes.
Our HSS (High Speed Steel) Taper Shank Bridge Reamers are designed for use in structural steel fabrication bridge work and ship construction to line up bolt and rivet holes. They can be used in portable electric or pneumatic equipment. These tools are also referred to as Boilermaker’s Reamers, Rivet Hole Reamers, Aligning Reamers, or Construction Taper Reamers.
Our HSS (High Speed Steel) Construction reamers are generally used to create bolt clearance holes when fastening steel beams, truck chassis etc.
Our HSS (High Speed Steel) Taper Pipe Reamers are designed for use in easy to ream materials. They are used prior to tapping dry seal and ANPT threads when high quality threads are required.
Atlas Cutting Tools stock an extensive range of over 15,000 Standard, Carbide, Cobalt and High Speed End Mills all USA manufactured to the highest standard. Our End Mills are all available with same day shipping at affordable prices. An End Mill is a type of milling cutter designed to be held by the shank on one end in order for it to cut with the opposite end. The advantage to an End Mill is that, unlike any other type of milling cutter, it is capable of cutting on the periphery, the face or the end of the cutter. At Atlas, our offering of End Mills is extensive-ranging from conventional HSS, Cobalt, and Solid Carbide Roughing & Finishing Mills to application and material specific tools employing the latest geometries and coating technologies all resulting in improved efficiency and productivity for you. The number of flutes can range from two to eight. The fewer flutes offer the most efficient chip removal, but a higher amount of flutes provide a smoother finish. The End Mill’s helix angle is also important. Most general purpose End Mills have a 30-degree helix angle because it is halfway between “slow” (low-angle) and “fast” (high-angle) helix End Mills. Specific projects require special styles of End Mills. Ball Nose End Mills are best for machining round bottom holes and complex contoured surfaces. Square Nose End Mills have square ends and are best for slotting, profiling, and roughing. Corner Radius End Mills have a square end with rounded corners on the cutting edges to reduce chipping. Double-ended End Mills have the same cutting edges and styles on both ends, doubling the tool’s life compared to Single-ended End Mills. Cutter material is an important consideration when selecting an end mill. Carbide End Mills can run at higher speeds than high-speed or cobalt steel, it is also more resistant to wear and can be used at high cutting temperatures. Cobalt Steel End Mills resists abrasion and high cutting temperatures, and has higher feed rates than High-speed Steel. High-speed Steel End Mills are compatible with a variety of materials and is typically used for less demanding jobs. An End Mill’s end cut type can either be center cutting or non-center cutting. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. All Carbide End Mills are center cutting. Non-center-cutting End Mills are suitable for peripheral milling and finishing, but cannot be used to make plunge cuts. HSS and Cobalt End Mills will specify if they are center or non-center cutting. Atlas Cutting Tools end mills offer a variety of coatings. Some end mills are uncoated, while others are coated with finishes to enhance performance. Most finishes extend the life of the End Mill and allow higher cutting speeds and feed rates.
What is the best End Mill for my application?
What is the best coating for my End Mill?
TiN (Titanium Nitride) End Mill Coating A special multilayer coating for edge retention and corrosion resistance when used on a wide range of materials including iron based, hardened steels, and stainless steels. Typically TiN is used in applications with lower cutting speeds than TiCN and ALTiN but often improves the tool's lifetime by a factor of three or more.
TiCN (Titanium Carbonitride) End Mill Coating A general purpose coating that offers improved wear resistance to abrasive, adhesive, or difficult to machine materials such as cast iron, aluminum alloys, steels, copper and more. This is a common used substitute when the advantages of ALTiN cannot be used, as in applications that cannot generate the speeds and feeds required for higher cutting temperatures. TiCN is harder and more impact resistant than TiN and can improve tool life by as much as 800%.
ALTiN (Aluminum Titanium Nitride) End Mill Coating This is a high performance coating for milling, tapping and drilling in stainless steels, carbon steels, alloy steels, and cast iron. This coating is extremely heat resistant and can be used with or without coolant. It is exceptional in difficult to machine materials where adhesive wear is particularly high and can be run at much higher speeds and feeds than all other coatings.
When it comes to drilling, there are many different types of drill bits available on the market, each designed to suit specific applications and materials.
Carbide Drills: Carbide drills are made from tungsten carbide, a very hard and durable material that can withstand high-speed drilling and maintain its sharpness for longer periods. They are ideal for drilling through harder materials such as composites, ceramics, and hardened steel. Atlas Cutting Tools carries the largest selection of solid Carbide Drills in a range of sizes, shapes and styles that are manufactured in the USA using the preeminent sub micro-grain carbide materials so as to provide utmost efficiency and performance. As compared to other elements, Carbide has higher levels of resistance to heat, wear and tear along with having a long working life. With that said, it is no wonder that carbide drill bits offered by us provide outstanding drilling solution for high production applications. Carbide drills provide faster cutting rates, extensive tool life and unmatched dimensional and positional precision and improved finish to the surface. Tighter tolerances and shorter cycle times of carbide drills ensures maximum utilization of the machineries and better quality of the parts while reducing the operational costs.
Cobalt Drills: Cobalt drills are made from high-speed steel alloy enriched with cobalt, which makes them tough and resistant to heat. They are ideal for drilling through tough and hard materials such as stainless steel, cast iron, and titanium. Cobalt drills are also more affordable than carbide drills, making them a good choice for general-purpose drilling applications where high precision and speed are not required.
HSS Drills: HSS drills (high-speed steel) are made from a steel alloy containing high amounts of tungsten, chromium, and vanadium. They are a versatile and durable option for drilling through materials such as wood, plastic, and soft metals. HSS drills are typically less expensive than carbide and cobalt drills, making them a popular choice for DIY and hobbyist projects.
Silver and Deming Drills: Silver and Deming drills are large diameter drills that feature a reduced shank diameter, making them compatible with standard drill chucks. They are often used in industrial applications that require large-diameter holes in materials such as steel, aluminum, and wood. Silver and Deming drills are available in both cobalt and HSS materials.
Choosing the right drill bit depends on the specific application and material being drilled. Carbide drills are ideal for precision drilling in harder materials, cobalt drills are suitable for drilling through tough and hard materials, HSS drills are versatile and affordable, and Silver and Deming drills are used for larger diameter holes in various materials. Understanding the advantages and applications of each drill bit type can help ensure the best results for your drilling project.
Atlas Cutting Tools stock a range of Carbide Burs, all of which are manufactured in the USA to exacting standards. We offer same day shipping and great affordable prices on our range of Carbide Burs. Single Cut Burs:
Atlas Cutting Tools range of high performance powered metal threading taps are precision manufactured in the USA and are available with same day shipping at affordable prices. Spiral Flute Taps – CNC Style These taps are manufactured with spiral flutes and evacuate chips out of a blind hole when tapping stringy-chip materials. Spiral flute taps are available for tapping medium carbon, alloy steels and stainless steels, aluminum, copper, soft to medium carbon and cast steels. These taps are very strong due to the increased core diameter and can run at greater tapping speeds and require less power to drive. Spiral Point Plug – CNC Style With a spiral gash in front of the cutting teeth, the spiral point gun tap forces the evacuation of chips ahead of the cutting action making these taps ideal for production tapping of through holes. These taps are very strong due to the increased core diameter and can run at greater tapping speeds and require less power to drive. Hand Taps
Chamfering work just got easier with Atlas Cutting Tools range of Solid Carbide Chamfer Mills. All our mills are USA precision manufactured and are available in single or double end, they offer superior quality, reliability and performance. We offer same day shipping and affordable prices on our range of Chamfer Mills. Solid Carbide Chamfer Mills Solid carbide chamnfer mills provide better rigidity than high speed steel. It is extremely heat-resistant and used for high speed applications on cast iron, nonferrous materials, plastics and other tough-to-machine materials. ALTiN Coated Chamfer Mills ALTIN is a high performance coating for milling, tapping and drilling in stainless steels, carbon steels, alloy steels, titanium and cast iron. This coating is extremely heat resistant and can be used with or without coolant. It is exceptional in difficult to machine materials where adhesive wear is particularly high and can be run at much higher speeds and feeds than all other coatings.
Atlas Cutting Tools supply high quality combination drill and countersinks. The combination of a drill and countersink tool is a perfect way of combining two tools in one; they can save a lot of money too. The combo drill and countersinks are used to efficiently create holes and cut countersinks – saving time and money. The combined drill and countersinks that we produce are very high quality. Double-ended and made from either solid carbide, high speed steel or premium cobalt. They are built to last and perform. Our combo drill and countersinks have a 60° included angle - all apart from a 90° HSS uncoated. The double ended combo drill and countersink tool is available coated and uncoated in a wide range of sizes. Features The Atlas Cutting Tools’ combined drill and countersinks are all USA manufactured, and by using exacting CNC specifications. They are all available with same day shipping at affordable prices. • 60° and 90° included angles • Double-ended • Solid carbide, HSS or premium cobalt • Made in the USA • Next day shipping. Premium cobalt combined drill and countersinks Cobalt combined drill and countersinks are great for cutting through hard metals like stainless steel and cast iron. Although, they can be used on softer materials too. HSS combined drill and countersinks High-speed steel drill and countersinks are tough, long-lasting and corrosion resistant. Especially good for drilling through stainless steel, cast iron and titanium. Solid Carbide drill and countersinks Our Carbide drill and countersinks are tough and are perfect for high volume production applications. They stay shaper for much longer than the high-speed steel.
Atlas Cutting Tools supply high quality combination drill and taps. The combination of a drill and tapping tool is a great way of combining two tools in one – they can save a lot of expense too. The combo drill and taps are used to create holes and cut threads in one – saving time and money. The helical flute design of both the drill and tap allows for the holes to be drilled and threads cut at relatively high speed. Our combo drill and taps are self-centering. They eliminate center punching or center drilling, and they reduce the required feed rates. To achieve optimal performance and extended tool life of the combination drill and tap; the use of suitable lubricating/cutting oils, or appropriate coolant fluids are recommended for most drilling and tapping operations. Atlas Cutting Tools stocks a wide range of high quality combo drill and taps. Various sizes are available for both standard and metric flutes. All drill and taps we supply are made from high-speed steel (HSS) and are corrosion resistant and built to last. HSS Combo drill and taps The Atlas Cutting Tools’ combo drill and taps are made from High Speed Steel (HSS). This gives all our combo drill and taps great resistance to corrosion and wear-and-tear. Our standard and metric combination drill and taps are all manufactured to precision standards in the USA. All our products are also available with same day shipping at affordable prices too. For general purpose, our high-speed steel combination drill and taps are suitable for drilling and tapping most materials. Suitable for both hand tapping and for use in production machines. These combo drill and taps achieve great accuracy in a wide range of material. • High-speed steel (HSS) • Combination drill & tap • 23 different sizes • Both standard and metric flutes.
Solid carbide thread mills are cutting tools that are designed to create precise and accurate threads in a variety of materials. These thread mills are made from high-quality solid carbide materials, which provides excellent wear resistance, toughness, and durability. They are perfect for threading holes, producing both internal and external threads with great efficiency and accuracy.
One of the main advantages of solid carbide thread mills is their ability to produce multiple forms of threads with a single tool. These thread mills can be used to create UN threads, UN coolant through threads, NPT pipe threads, NPTF pipe threads, and metric threads. This versatility makes them a great choice for machinists who work with a wide range of materials and thread types.
Solid carbide thread mills with UN threads are designed to create unified threads, which are commonly used in the United States and other countries that follow American standards. These thread mills are available in a range of sizes and can be used to create both internal and external threads.
UN coolant through threads are used in applications where coolant or other fluids need to be delivered through the threaded hole or component. Solid carbide thread mills with UN coolant through threads are designed to create these specialized threads with precision and accuracy.
NPT pipe threads are commonly used in the plumbing and piping industry, particularly in North America. These threads have a tapered design, which creates a tight seal between two components. Solid carbide thread mills with NPT pipe threads can be used to create these threads in a range of sizes, making them a versatile option for machinists in this industry.
NPTF pipe threads are similar to NPT pipe threads, but they have a modified thread form that creates a leak-proof seal without the use of thread sealant. Solid carbide thread mills with NPTF pipe threads are designed to create these specialized threads with precision and accuracy.
Metric threads are commonly used in Europe and other countries that follow the metric system. Solid carbide thread mills with metric threads are available in a range of sizes and can be used to create both internal and external threads with precision and accuracy.
In conclusion, solid carbide thread mills are a versatile and efficient cutting tool that can be used to create a wide range of thread forms. Whether you need to create UN threads, UN coolant through threads, NPT pipe threads, NPTF pipe threads, or metric threads, there is a solid carbide thread mill available to meet your needs. These tools offer exceptional wear resistance, toughness, and durability, making them an excellent choice for machinists who demand high-quality and reliable cutting tools.
Countersinks are required when the head of a bolt or screw needs to be countersunk. They are prefect for deburring and chamfering openings to pre-drilled holes. Atlas Cutting Tools stock a range of countersinks to cater for all needs. Our wide selection of countersinks are built to be used on a variety of different materials. And they will always cut cleanly and accurately. Our products are made to very high standards and are available in high-speed steel (HSS) or with super hard carbide heads. These countersinks are built last and to perform in even the toughest materials.
HSS Countersinks Our High-speed steel countersinks are coated with black oxide to increase corrosion resistance. They are suitable for use on nearly all materials and will create a chatter and burr-free finish.
Solid Carbide Countersinks The solid carbide countersinks provide better rigidity than high-speed steel. It is extremely heat resistant and used for high-speed applications on cast iron, nonferrous materials, plastic and other tough-to-machine materials. The Atlas Cutting Tools’ countersinks are precision manufactured in the USA and are available with same day shipping at affordable prices. Features • Super hard solid carbide heads, or • Corrosion resistant high-speed steel (HSS) • Wide selection of sizes and flute tips • All made in the USA • Same day shipping
Atlas Cutting Tools manufacture first-class adjustable round split dies. They come in both carbon steel and high-speed steel (HSS). The round split carbon steel dies are adjustable for precision threading of bolts, studs, rods and other pieces that require external threading. Our round split steel dies are ideal for cleaning internal and external threads. All our dies are precision manufactured in the USA and are available with same day shipping at affordable prices. Atlas Cutting Tools’ carbon and HSS dies are for threading rods, bolts, studs or similar applications where external threads are required. Our round split dies are produced as round cutters with an adjustable screw to force the die to widen or narrow. This allows the die to cut to all standard thread classes. The high-speed steel (HSS) dies are corrosion resistant and will increase the longevity and durability of the die. They are the ideal cutting tool for larger volume productions. Both the Carbon steel and the high-speed steel dies that we manufacture are perfect for use with a variety of steels and steel alloys, and a range of non-ferrous materials, too. Features of our adjustable round split dies:
Atlas Cutting Tools’ precision engineered steel drill drifts are wedge-shaped drifts that are specifically designed removing tapered shank tools from the spindles, sockets or sleeves. Oxide finish drill drift Our oxide finished drill drifts last longer than most other drill shifts. They will make light work of removing taper mount chucks from arbors. Made with exacting precision from high-speed steel, we finish them with an oxide coating. This oxide coating increases durability and adds anti-corrosion properties. HSS Screw Extractors We also have a very large variety of high-speed steel screw extractors. They are ideal for removing any broken or seized screws. We manufacture 12 different sizes of screw extractors that will match most screw extraction requirements. To save time and money we also sell a set of screw extractors from sizes 1 to 5. Features of our drill drifts and screw extractors:
Atlas Cutting Tools’ drill drifts and screw extractors are precision manufactured in the USA and are all available with same day shipping at affordable prices.
Atlas Cutting Tools manufacture a large range of precision solid Carbide drill mills. Our solid Carbide drill mills are all manufactured in the USA, and to extremely high standards. Solid Carbide drill mills are the perfect multi-purpose tool that will save money and time. They add versatility and functionality to your milling machine. Use them to chamfer, spot drill, drill, countersink or side mill. Using solid Carbide means these drill mills will last, and stay sharp for much longer. They are available uncoated or with an AlTiN (Aluminium Titanium Nitride) coating. This added coating will allow for a higher running speed. It also prevents metal chips from sticking to the End Mill for better performance and cleaner cuts. The thermal stability of all our solid carbide drill mills mean they are perfect for volume work. Atlas Cutting Tools can supply both the two flute and 4 flute tips, all with a 30 degree Helix. They are also available in both 60 and 90 degree points, coated with AlTiN, or left uncoated. All our drill mills are precision manufactured in the USA and are available with same day shipping at affordable prices. Features of our solid Carbide drill mills
Atlas Cutting Tools have put together various drilling and cutting sets to fit most requirements. We have included sets that are manufactured in cobalt, black and gold, high-speed steel (HSS) and silver/deming. Purchasing our tool sets mean great cost savings can be had while ensuring that drilling and cutting tools are of high quality that will last. Our full range of sets includes:
All sizes have been accommodated in our drilling and cutting sets and they are all supplied in a bespoke carry case to keep them safe in one place. Atlas Cutting Tools sets offer exceptional value. Every item in our drill sets is manufactured in the USA and are available with same day shipping at affordable prices.